自动上料搅拌车发动机水温过高的方法
Automatic feeding mixer belongs to special special operation vehicle, it has a specific working environment, the engine water temperature will inevitably be too high. In some cases, the water temperature of the cylinder head will burst seriously. If you continue to drive, there is the possibility of cylinder pulling, then the solution of excessive engine water temperature of automatic feeding mixer truck
一、自动上料搅拌车发动机水温过高的方法
1、 Solution to the problem of high water temperature in the engine of automatic feeding mixer
1、自动上料搅拌车在普通公路上发动机出现了过热,应该尽快地降低车速,把汽车驶到树荫下,或驶到相对比较凉快的地方,把汽车停下来,但这时候不要急于熄火。
1. The engine of the automatic feeding mixer truck is overheated on ordinary roads. It is necessary to reduce the speed as soon as possible, drive the vehicle into the shade of trees, or drive to a relatively cool place, and stop the vehicle, but do not rush to turn off the engine at this time.
2、打开发动机罩盖,让发动机怠速运转,等待发动机温度逐渐恢复正常。在发动机水温恢复正常之后,将发动机熄火,然后再等待一段时间,直到发动机的水温充分地下降了之后,再检查发动机的冷却水量。
2. Open the engine cover, let the engine idle and wait for the engine temperature to gradually return to normal. After the engine water temperature returns to normal, turn off the engine, and then wait for a period of time until the water temperature of the engine drops sufficiently, and then check the cooling water volume of the engine.
3、这时候自动上料搅拌车发动机的冷却水量可能大都严重不足。按着规定量把冷却水补足之后,再检查一下冷却系统,确认没有其他故障之后,可以起动发动机,继续行驶。也要检查一下水箱百叶窗是不是被异物堵塞,风扇叶的工作情况,发动机皮带是否打滑,发动机水泵工作情况等。
3. At this time, the cooling water of the engine of the automatic feeding mixer may be seriously insufficient. After making up the cooling water according to the specified amount, check the cooling system again, and after confirming that there are no other faults, you can start the engine and continue driving. Also check whether the louver of water tank is blocked by foreign matters, the working condition of fan blade, whether the engine belt slips or not, and the working condition of engine water pump.
4、如果在高速公路上出现了发动机过热,必须立刻把暖风全部打开并打开车窗,这时车厢内将热得像地狱一样。由于有暖风帮助冷却水散热,能使冷却水温大幅度地下降。这样可以持续开车,就近找到高速公路的出口,将搅拌车驶到的场所停下来。接下来,只要按照上述的方法,使发动机的温度降下来就行。注意,不要把搅拌车停在路边,以免影响交通或被撞车,必须把搅拌车停在的场所。
4. If the engine overheats on the highway, you must turn on all the warm air and open the windows immediately. At this time, the car will be as hot as hell. Due to the warm air to help the cooling water dissipate heat, the cooling water temperature can be greatly reduced. In this way, you can continue to drive, find the exit of the expressway nearby, and drive the mixer to a safe place to stop. Next, as long as the above method, so that the engine temperature down on the line. Note that it is best not to park the mixer on the side of the road, so as not to affect the traffic or be hit. The mixer must be parked in a safe place.
因此发现自动上料搅拌车发动机水温过高一定要采取措施,避免搅拌车出现严重故障,为了大家更好的了解相关的知识,下面小编和大家讲解一下自上料搅拌车发动机水箱温度过高的因素,及发动机的保养方法,希望可以帮助到大家。
Therefore, it is necessary to take measures to avoid serious failure of the mixer when it is found that the water temperature of the engine is too high. In order to better understand the relevant knowledge, the following editor will explain the factors that cause the engine water tank temperature to be too high and the maintenance methods of the engine, hoping to help you.