服务热线:
400-879-1999
栏目导航
联系我们
服务热线
400-879-1999
电话:400-879-1999
地址:山东省莱州市206国道与308省道交叉口东南50米
当前位置:首页 > 搅拌车资讯 > 新闻资讯中科自动上料搅拌车轮胎被扎破处理方法?
中科自动上料搅拌车轮胎被扎破处理方法?
来源:http://www.cnzkjf.cn发布日期:2021-01-08   浏览量:0
 
中科自动上料搅拌车因为工作的需要,常常行驶在各种地方,因此,在路上行驶的时候有可能被尖锐的物品划破车轮胎,下面就来为您介绍如果轮胎被划破了应该怎样进行补救。
Due to the need of work, Zhongke automatic feeding mixer often runs in various places. Therefore, when driving on the road, it may be scratched by sharp objects. Here is how to remedy if the tire is scratched.
一、急救式:打枪补
1、 First aid: shot to repair
中科自动上料搅拌车常见的补胎方式是在轮胎的扎洞部位塞入特制胶条,补胎店的师傅通常将它称为打枪式补胎。这种方法的较大好处是快捷方便,只需要几分钟,而且也不需要将轮胎从钢圈上撬下来,而打枪式补胎的缺陷是不够耐用,另外还很难应付较大的创口,自动上料搅拌车因此通常只能作为一种临时性的补救措施。
The common tire repair method of Zhongke automatic feeding mixer is to insert a special rubber strip into the hole of the tire. The master of the tire repair shop usually calls it gun type tire repair. The great advantage of this method is that it is fast and convenient, only takes a few minutes, and does not need to pry the tire off the rim. The defect of gun type tire repair is that it is not durable enough. In addition, it is difficult to deal with large wounds. Therefore, the automatic feeding mixer can only be used as a temporary remedy.
二、堵缺式:粘贴补
2、 Plugging type: sticking and patching
还有一种补胎方式是粘补。所谓粘补是将自动上料搅拌车受伤轮胎从钢圈上卸下,找到创口后,从轮胎内层贴上专用的补胎胶皮,从而完成补漏。这种方法的优点是可以对中科自动上料搅拌车较大的创口进行修补,缺点是不够耐用,在经过一段时间的水浸和高速运转后,解放自动上料搅拌车修补处会再次出现漏气。
There is also a way to repair the tire is sticking. The so-called patching is to remove the injured tire of the automatic feeding mixer from the steel ring, and after finding the wound, paste the special patching rubber from the inner layer of the tire, so as to complete the patching. The advantage of this method is that it can repair the larger wound of Zhongke automatic feeding mixer, but the disadvantage is that it is not durable enough. After a period of water immersion and high-speed operation, air leakage will appear again at the repair place of Jiefang automatic feeding mixer.
三、终结式:火补
3、 Ending: Huobu
彻底的补胎措施是常说的火补。火补同样要撬下轮胎,然后将专用的生胶片贴附于创口,用烘烤机对创口进行烘烤,直生胶片与轮胎完全贴合。火补的好处是非常耐用,基本不用担心会重复漏气。
Thorough tire repair is often called fire repair. The fire mending also needs to pry off the tire, then attach the special raw rubber sheet to the wound, and bake the wound with a baking machine until the raw rubber sheet completely fits the tire. The advantage of fire repair is that it is very durable and there is no need to worry about repeated air leakage.
不过它也有缺点,那就是施工时的技术要求较高,因为一旦烘烤时的火候控制不好,很可能会将自动上料搅拌车轮胎烤焦,严重的还会产生变形,自动上料搅拌车液压机那样一来,对轮胎的损伤可就大了。
However, it also has disadvantages, that is, the technical requirements during the construction are high, because once the temperature control during baking is not good, it is likely to scorch the tires of the automatic feeding mixer, and even produce serious deformation. The hydraulic press of the automatic feeding mixer will cause great damage to the tires.
中科自动上料搅拌车轮胎的修补方法就分享到这里,希望能给您带来帮助。如果还有不明白的地方,可以关注:http://www.cnzkjf.cn会呈现更多的精彩内容。
This is how to repair the tire of Zhongke automatic feeding mixer. I hope it can help you. If you still don't understand, you can pay attention to: http://www.cnzkjf.cn There will be more wonderful content.

莱州中科聚峰机械有限公司 电话:15053524111 地址:山东省莱州市206国道与308省道交叉口东南50米