服务热线:
400-879-1999
栏目导航
联系我们
服务热线
400-879-1999
电话:400-879-1999
地址:山东省莱州市206国道与308省道交叉口东南50米
当前位置:首页 > 搅拌车资讯 > 常见问题自动混凝土搅拌车“发动机损坏”
自动混凝土搅拌车“发动机损坏”
来源:http://www.cnzkjf.cn发布日期:2021-06-15   浏览量:0
 
自动混凝土搅拌车一定为所有人所熟知。自动混凝土搅拌车被用在很多地方,自动混凝土搅拌车也起着非常重要的作用。当使用诸如搅拌机轨道之类的小的搅拌机轨道时,总是出现相应的问题。
The automatic concrete mixer must be well known to everyone. Automatic concrete mixer is used in many places, automatic concrete mixer also plays a very important role. When using small mixer tracks such as mixer tracks, there are always corresponding problems.
一些小型搅拌车司机报告说,如果他们与朋友同时购买同一辆搅拌车,他们在使用汽车一段时间后会遇到发动机问题,但是他们朋友的汽车的发动机很好。发生了什么?混合器引擎为什么会这么快破裂?让我们看看是否使用不当或车辆本身有问题。
Some small mixer drivers report that if they buy the same mixer with a friend at the same time, they will encounter engine problems after using the car for a period of time, but their friend's car has a good engine. What happened? Why did the mixer engine break down so quickly? Let's see if it's not used properly or if there's something wrong with the vehicle itself.
自动混凝土搅拌车
1.自动混凝土搅拌车上的维护数据使用不当
1. Improper use of maintenance data on automatic concrete mixer
在自动混凝土搅拌车的维护中,无法科学地选择维护数据是零件过早损坏的重要原因。例如,在进气门的情况下,气门与阀座之间的接触面的宽度为1.2.2mm,在排气门的情况下,宽度为1.5.2.5mm。,但在实际维护中,宽度是变大和变窄,应该大于。许多人说这很好,通常将上限选择为上限或接近上限。
In the maintenance of automatic concrete mixer, the failure to select maintenance data scientifically is an important reason for premature damage of parts. For example, in the case of intake valve, the width of contact surface between valve and valve seat is 1.2.2mm, in the case of exhaust valve, the width is 1.5.2.5mm., But in the actual maintenance, the width is larger and narrower, should be greater than. Many people say that's good, and usually choose the upper limit as the upper limit or close to the upper limit.
新车的气门工作面宽度已经接近使用限,因此是上限。另一个例子是阀脚间隙。车辆通常指定为0.2-0.25毫米。但是,维护调整认为差距要大于较小的差距。因此,如果间隙超过上限,则间隙实际上会变得太大,不仅降低了发动机功率,而且还由于冲击而引起了初始损坏。
The width of the valve working surface of the new car is close to the service limit, so it is the upper limit. Another example is the valve foot clearance. Vehicles are usually specified as 0.2-0.25 mm. However, the maintenance adjustment believes that the gap is greater than the smaller gap. Therefore, if the clearance exceeds the upper limit, the clearance will actually become too large, which not only reduces the engine power, but also causes initial damage due to impact.
2.平稳地压碎自动混凝土搅拌车的阀门
2. Crush the valve of automatic concrete mixer smoothly
如果阀门有消融,凹坑或凹痕以保持小型搅拌车,则通常需要使用抛光研磨机对其进行研磨。在操作过程中要注意四个问题。,检查阀头和阀杆。同心圆,否则您需要先修复它们。接下来,假设您可以抛光完 美的圆锥,则需要使光滑的汽车尽可能小。接下来,您需要进行表面抛光。第四方面应尽可能提高以平滑阀杆的凹入端。
If the valve has ablation, pits or dents to keep the small mixer, it usually needs to be ground with a polishing grinder. In the process of operation, we should pay attention to four problems. First, check the valve head and stem. Concentric circles, otherwise you need to fix them first. Next, assuming you can polish the perfect cone, you need to make the smooth car as small as possible. Next, you need to polish the surface. The fourth aspect should be raised as much as possible to smooth the concave end of the stem.

莱州中科聚峰机械有限公司 电话:15053524111 地址:山东省莱州市206国道与308省道交叉口东南50米