服务热线:
400-879-1999
栏目导航
联系我们
服务热线
400-879-1999
电话:400-879-1999
地址:山东省莱州市206国道与308省道交叉口东南50米
当前位置:首页 > 搅拌车资讯 > 常见问题中科搅拌机是如何进行打孔工作的?
中科搅拌机是如何进行打孔工作的?
来源:http://www.cnzkjf.cn发布日期:2020-11-18   浏览量:0
 
 搅拌机并不难打,但很多人不太清楚如何操作搅拌机。其实中科搅拌机打孔技术并不难操作,你看完下面的内容后就知道怎么打孔了。
  The mixer is not hard to beat, but many people don't know how to operate it. In fact, the drilling technology of Zhongke mixer is not difficult to operate. You will know how to drill after reading the following content. Please refer to:
  随着科学技术的发展,应用市场的需求,搅拌机越来越快速的发展,需求也在不断上升,每个人都很熟悉它,但仍有少量的客户不知道搅拌机的穿孔技巧,以下是介绍搅拌机的穿孔的技能:
中科搅拌机
  With the development of science and technology, the demand of the application market, the mixer is developing more and more rapidly, and the demand is also rising. Everyone is familiar with it, but there are still a small number of customers who do not know the perforation skills of the mixer. The following is an introduction to the perforation skills of the mixer:
  1. 搅拌机的射孔支管不得使用电焊(气焊)工具,因为电焊会破坏搅拌机的内衬塑料,支管的连接必须用专用管件进行坡口连接;
  1. Electric welding (gas welding) tools shall not be used for the perforating branch pipe of mixer, because electric welding will damage the inner plastic of mixer, and the connection of branch pipe must be beveled with special pipe fittings;
  2. 在钻孔过程中,塑料渣衬很容易掉入混合器原管道中,所以在操作过程中要多加注意,否则会堵塞末端水点;
  2. In the process of drilling, the plastic slag lining is easy to fall into the original pipeline of the mixer, so pay more attention in the operation process, or the end water point will be blocked;
  3.虽然钻孔时内衬塑料相对较软,但使用刚性钻头易强行破坏搅拌机,且边角不易平整。
  3. Although the lining plastic is relatively soft when drilling, the mixer is easy to be damaged by force when using a rigid drill bit, and the corners are not easy to be flat.
  不要在有孔的分支上使用焊接工具,因为这样会损坏衬层。
  Do not use welding tools on the branch with holes, as this will damage the lining.
  5. 当钻孔时,残渣会掉入玻璃衬混合器,所以操作时请注意,否则会造成堵塞。
  5. When drilling, the residue will fall into the glass lining mixer, so please pay attention to the operation, otherwise it will cause blockage.

中科搅拌机
  6. 由于玻璃衬里搅拌器的衬里是软的,钻头会损坏。另外,边角不整齐。
  6. Because the lining of the mixer with glass lining is soft, the drill bit will be damaged. In addition, the corners are not neat.
  一般情况下,看完以上内容后,就可以熟练掌握搅拌机打孔了,希望对使用搅拌机能起到一定的帮助。
  In general, after reading the above content, you can master the drilling of the mixer skillfully, hoping to play a certain role in using the mixer.
  以上是中科搅拌机厂家为大家介绍的相关内容,想要了解更多内容,欢迎访问网站:http://www.cnzkjf.cn
  The above content is introduced by the mixer manufacturer of China Science and Technology Co., Ltd. for more information, please visit the website:http://www.cnzkjf.cn
 

莱州中科聚峰机械有限公司 电话:15053524111 地址:山东省莱州市206国道与308省道交叉口东南50米