服务热线:
400-879-1999
栏目导航
联系我们
服务热线
400-879-1999
电话:400-879-1999
地址:山东省莱州市206国道与308省道交叉口东南50米
当前位置:首页 > 搅拌车资讯 > 常见问题自动上料搅拌车使用过程中钢板容易破裂的原因是什么?
自动上料搅拌车使用过程中钢板容易破裂的原因是什么?
来源:http://www.cnzkjf.cn发布日期:2020-08-10   浏览量:0
 
自动上料搅拌车的前钢板由九块组成。许多人报告说,自动搅拌上料机的和第二部分在使用过程中容易破裂是什么原因?
The front steel plate of the automatic mixing and feeding machine is composed of nine pieces. Many people have reported that the first and second parts of the automatic mixing and feeding machine are easy to crack during use?
(1)过度使用紧急制动器。在山上行驶时,在下坡路上使用紧急制动器可能会损坏前板。由于制动力,自动搅拌上料机的大部分负荷质量得到前板簧的促进和接受。结果,可能发生片簧的疲劳损坏。建议使用排气制动器以减少紧急制动。
(1) Excessive use of emergency brakes. Using the emergency brake on a downhill road may damage the front panel when driving on a hill. Due to the braking force, most of the load mass of the automatic mixing feeder is promoted and accepted by the front leaf spring. As a result, fatigue damage of the leaf spring may occur. Exhaust brakes are recommended to reduce emergency braking.
(2)前轮制动调整太紧。如果后轮制动性能不佳,或者发生突然问题,请使用紧急制动器并通过过度冲击破坏前板簧。
(2) Front wheel brake adjustment is too tight. If the braking performance of the rear wheels is poor or sudden problems occur, use the emergency brake and destroy the front leaf spring by excessive impact.
(3)路面不好,超载,超速,对前板簧施加过大的冲击力,容易造成损坏。
(3) The road surface is not good, overload, overspeed, and the front leaf spring is subject to excessive impact force, which is easy to cause damage.
(4)前板簧经常长时间过载,降低弹性和刚性,并因疲劳而损坏。
(4) The front leaf spring is often overloaded for a long time, which reduces elasticity and rigidity, and is damaged due to fatigue.
(5)更换低质量的板簧。刀片弯曲不符合标准。由于钢板材料不好或热处理不好,应力变得不均匀和断裂。
(5) Replace the low quality leaf spring. The blade bending does not meet the standard. Due to the poor material or heat treatment of steel plate, the stress becomes uneven and fracture.
为防止自动搅拌上料机前板簧的和第二块自动装载,我们建议采用以下方法:
In order to prevent the automatic loading of the first and second pieces of the front leaf spring of the automatic mixing feeder, the following methods are recommended:
(1)检查时间,确保板簧良好润滑,并正确调整车辆制动器。
(1) Check the time to ensure that the leaf spring is well lubricated and the vehicle brake is adjusted correctly.
(2)减少紧急制动器的使用,增加发动机排气制动器的使用,均匀地施加载荷而不会过载。
(2) Reduce the use of emergency brake, increase the use of engine exhaust brake, evenly apply load without overload.
(3)更换前钢板时,必须使用钢板,以确保弯曲度符合要求。使用山东弹簧厂和重庆弹簧厂生产的板簧。
(3) When replacing the front steel plate, high-quality steel plate must be used to ensure that the bending meets the requirements. It is better to use the leaf spring produced by Shandong spring factory and Chongqing Spring Factory.
(4)在不平坦的道路上行驶或下坡行驶时,需要控制自动搅拌上料机的速度并在曲线上行驶。不要急于过快。
(4) When driving on uneven road or downhill, it is necessary to control the speed of automatic mixing feeder and drive on the curve. Don't rush too fast.
自动搅拌上料机传动油品质检测方法
Quality inspection method for transmission oil of automatic mixing and feeding machine
1.将自动搅拌上料机放在平坦的表面上并拧紧手制动器。
1. Place the automatic mixing feeder on a flat surface and tighten the hand brake.
2.让发动机空转几分钟。
2. Let the engine idle for a few minutes.
3.踩下制动踏板并转动操纵杆前后移动。将每个齿轮移动几秒钟以填充变矩器和所有带液压油的换档执行器。,将操纵杆转到停车位置。
3. Step on the brake pedal and turn the control lever to move forward and backward. Move each gear for a few seconds to fill the torque converter and all shift actuators with hydraulic oil. Finally, turn the lever to the park position.
4.从加注管上取下自动量油尺,将清洁的量油尺插入加油管并将其拉出以检查量油尺的油位。
4. Remove the automatic dipstick from the filler tube, insert the clean dipstick into the filler tube and pull it out to check the oil level of the dipstick.
在检查或排除自动搅拌上料机故障之前,检查变速箱油位和油质。换档杆必须处于P位置,发动机应在空转时运转少几分钟,液体将达到正常工作温度,并且车辆必须停在水平面上以确保差速器和节气门之间的油位。通常传输是稳定的。
Check the oil level and oil quality of the gearbox before checking or troubleshooting the automatic mixing feeder. The shift lever must be in the P position, the engine should be running at idle for at least a few minutes, the fluid will reach normal operating temperature, and the vehicle must be stopped on a level surface to ensure the oil level between the differential and the throttle. Usually the transmission is stable.
自动上料搅拌车的钢板断裂和传动油质量检查问题介绍就是这样了,希望对你有帮助。
Automatic mixing feeder steel plate fracture and transmission oil quality inspection problem introduction is like this, hope to help you.

莱州中科聚峰机械有限公司 电话:15053524111 地址:山东省莱州市206国道与308省道交叉口东南50米