1、 The overall dimensions of the whole vehicle shall conform to the provisions of national standards. It shall be manufactured according to the approved product drawings and technical documents.

二、外购件、外协件均应有制造厂的产品合格证，并符合相关标准的要求，经搅拌车生产厂检验合格后方可装配。

2、 Purchased parts and outsourced parts shall be provided with the product certificate of the manufacturer and meet the requirements of relevant standards. They can be assembled only after passing the inspection of the mixer manufacturer.

三、搅拌车的厂定大总质量不得超过底盘的大许用值，转向轴(轮)载质量和侧倾稳定角应符合GB7258的规定。

3、 The factory determined total mass of the mixer shall not exceed the allowable value of the chassis, and the steering shaft (wheel) load mass and roll stability angle shall comply with the provisions of GB7258.

点击进入看图评论

Click to view the comments

四、焊缝应均匀、平直。无漏焊、裂纹、央渣、表面应无毛边，包砂等现象。

4、 The weld shall be even and straight. There shall be no missing welding, crack, slag, rough edge and sand inclusion on the surface.

五、所有外露黑色金属表面均应作防锈处理。外表装饰漆应美观大方，符合GB7258的规定。

5、 All exposed ferrous metal surfaces shall be rust proof. The exterior decorative paint shall be beautiful and generous, and conform to the provisions of GB7258.

六、从进料到输送卸料完毕，允许的长时间为90mh，且搅拌筒按规定连续运输不大于300转。搅拌车行驶时，高车速不得超过如50km/h

6、 The allowable long time from feeding to unloading is 90mh, and the continuous transportation of the mixing drum is no more than 300 revolutions according to the regulations. When the mixer is running, the high speed shall not exceed 50km / h

七、装入预拌混凝土在规定的搅动转速和输送时间运送到交贷地点后，泥凝土质量应符国标要求。

7、 After the ready mixed concrete is loaded and transported to the delivery place at the specified agitation speed and delivery time, the quality of the mud concrete shall meet the requirements of the national standard.

八、进料斗出口尺寸不小于历650mm，距地面高度应不大于3.8m。

8、 The outlet size of the feed hopper shall not be less than 650mm, and the height from the ground shall not be more than 3.8m.

九、水泥搅拌车的出料速度不小于0.65m3/min，出料残余率小于2-5%。搅拌车的进料速度不小于2.7m3/min

9、 The discharging speed of cement mixer shall not be less than 0.65m3/min, and the discharging residual rate shall be less than 2-5%. The feeding speed of the mixer shall not be less than 2.7m3/min

十、输送应安装牢固。各连接部分部件不应有损坏、变形等现象，不应有上车与底盘偏离原先的固定装置的情况。

10、 The conveying shall be installed firmly. All connecting parts shall be free of damage, deformation and other phenomena, and there shall be no deviation between the upper carriage and the chassis from the original fixed device.

十一、车在大总质量状态下，以20km/h的速度府能通过14%的坡道外溢。

11、 Under the condition of large total mass, the vehicle can pass 14% of the ramp at the speed of 20km / h.

十二、制动性能府符合国标规定。行驶车外噪声应符国标要求。

12、 The brake performance meets the national standard. The noise outside the driving vehicle shall meet the requirements of the national standard.

十三、整车的各项密封性能良好，各密封面、管接头及所有连接部位均不得有渗油漏气的现 象。

13、 The sealing performance of the whole vehicle is good, and all sealing surfaces, pipe joints and all connecting parts shall be free of oil leakage.

本文来自：中科聚峰厂家更多的内容请点击：http://www.cnzkjf.cn我们将会为您提问的问题提供一个满意的服务，欢迎您的来电！

This article comes from: Zhongke Jufeng factory more content please click: http://www.cnzkjf.cn we will provide a satisfactory service for your questions, welcome your call!