服务热线:
400-879-1999
栏目导航
联系我们
服务热线
400-879-1999
电话:400-879-1999
地址:山东省莱州市206国道与308省道交叉口东南50米
当前位置:首页 > 搅拌车资讯 > 新闻资讯使用搅拌设备加氢时需要注意什么呢?
使用搅拌设备加氢时需要注意什么呢?
来源:http://www.cnzkjf.cn发布日期:2020-04-20   浏览量:0
 
传统的拌和设备多为轴流拌和器,但在长时间的运用过程中发现,轴流拌和器对于一些需求进液分离的物料反响往往不够大。于是,工程师研发了一种新型的,就是加氢拌和器。这种的特点在于中间参加氢,这使得气体和液体之间可以被氢气切割,到达较好的反响作用。加氢拌和器中的氢是消耗品,所以需求对其进行定期增加才干保障反响釜的正常工作。
The traditional mixing equipment is mostly axial-flow mixer, but in the long-term application process, it is found that the response of axial-flow mixer to some materials requiring gas-liquid separation is often not enough. So, engineers developed a new type of mixer, which is hydrogenation mixer. This kind of characteristic lies in the participation of hydrogen in the middle, which makes the gas and liquid can be cut by hydrogen to achieve a better reaction. Hydrogen in the hydrogenation mixer is a consumable, so it needs to be increased regularly to ensure the normal operation of the reaction kettle.
在加氢的时分需求先将反响釜的各个阀门封闭,且对其进行检查,排除漏气的状况。其次再降里边的无用空气利用真空的原理排光,此时方可将它的阀门翻开开始加氢。但刚开始加氢为测验,不需参加太多。参加少量之后测验密封性和压力是否正常。若是正常则继续往内加氢。
中科搅拌车
At the time of hydrogenation, it is required to first close all valves of the reaction kettle and check them to eliminate the air leakage. Secondly, reduce the useless air inside to use the principle of vacuum to discharge light, then turn over its valve and start hydrogenation. But at the beginning, hydrogenation is a test, so you don't need to take too much part in it. Take a few tests to see if the sealing and pressure are normal. If it is normal, continue to hydrogenation.
它的加氢整体过程仍是相对较为简单的,但要注意的是,这是在设备完好的状况下完成的。
The whole process of hydrogenation is still relatively simple, but it should be noted that it is completed under the condition of intact equipment.
拌和设备的加氢过程是有考究的,那么在运用的时分了解该其中的过程是很重要的。
The hydrogenation process of mixing equipment is well studied, so it is very important to understand the process during operation.
1、检查其各阀门是否关严,将排气软管指向空阔且空气流通的地方。
1. Check whether the valves are closed tightly, and point the exhaust hose to the place with wide air flow.
2、上氢气减压阀门、氮气压力阀,上好后,用肥皂水检查是否漏气。
2. Install the hydrogen pressure reducing valve and nitrogen pressure valve, and then use soapy water to check for air leakage.
3、在排气口用真空抽出液面上的空气。
3. Vacuum out the air on the liquid level at the exhaust port.
4、翻开它的进气阀,翻开氮气减压阀,充氮气,使内釜压力后,封闭氮气,减压阀,封闭进气阀,保持约两分钟,看压力表压力是否下降,另外釜盖是否漏气,如没漏,则缓慢翻开排气阀,将里边的压力分泌0.01Mpa时,封闭排气阀。此过程再重复1次。
4. Open its air inlet valve, open the nitrogen pressure reducing valve and fill it with nitrogen. After the pressure of the inner kettle is reached, close the nitrogen, pressure reducing valve and air inlet valve and keep them for about two minutes to see whether the pressure of the pressure gauge drops. In addition, check whether the kettle cover leaks air. If there is no leakage, slowly open the exhaust valve. When the pressure inside is secreted to 0.01Mpa, close the exhaust valve. Repeat this process one more time.
5、翻开进气阀,翻开氢气减压阀,充入氢气所需压力,封闭进气阀,封闭氢气减压阀,然后调试拌和器其它参数所需状态令其反响。
5, turn on the intake valve, turn on the hydrogen pressure reducing valve, charge the hydrogen to the required pressure, close the intake valve, seal the hydrogen pressure reducing valve, and then adjust other parameters of the mixer to respond to the required state.
本文由中科搅拌机整理发布,您是不是对这些内容有所了解了呢?更多的内容请点击:http://www.cnzkjf.cn我们会有更多精彩内容等你查看。
This article is published by the price arrangement of mixer of China Science and Technology Corporation. Do you know something about these contents? For more information, please click: http://www.cnzkjf.cn and we will have more wonderful contents for you to see.

莱州中科聚峰机械有限公司 电话:15053524111 地址:山东省莱州市206国道与308省道交叉口东南50米