In the introduction of automatic concrete mixer detection steps, let everyone know some unknown problems or knowledge, but we are still relatively unfamiliar with our industry. Today we will gradually understand that:

1.电池维护检查：检查电池是否牢固固定。

1. Battery maintenance inspection: check whether the battery is firmly fixed.

2.轮胎检查：每月应检查室温下的轮胎压力。

2. Tire inspection: check the tire pressure at room temperature every month.

3.离合器主泵水位检查：离合器液位高低液位表示正常，如果低于标准线，则可能是主泵或泵碗损坏。

3. Check the water level of clutch main pump: the high and low liquid level of clutch indicates that it is normal. If it is lower than the standard line, the main pump or pump bowl may be damaged.

4.检查制动液液位：制动液在高低之间也正常。

4. Check the brake fluid level: the brake fluid is normal between high and low.

5.发动机冷 却液液位检查：当发动机处于高温状态时，不要打开散热器盖，否则可能会被飞溅的冷 却液或高温蒸汽灼伤。发动机冷 却后，检查冷 却液的液位应在满和低之间。否则，应加入蒸馏水或纯净水或冷冻液。加水后液体的高度不应超过满水位。如果发现冷 却液在短时间内迅速降低，则自动混合器检查步骤应检查冷 却系统是否有泄漏或者到维修站进行检查。

5. Engine coolant level inspection: when the engine is at high temperature, do not open the radiator cap, otherwise it may be burned by splashing coolant or high temperature steam. After the engine is cooled, check that the coolant level should be between full and low. Otherwise, distilled water or purified water or frozen liquid should be added. After adding water, the liquid height should not exceed the full water level. If it is found that the coolant drops rapidly in a short time, the automatic mixer inspection procedure should check whether the cooling system has leakage or go to the maintenance station for inspection.

混凝土全自动搅拌车驱动器介绍

Introduction of driver for automatic concrete mixer

驱动器用于驱动混凝土罐的旋转。它由动力输出单元，万向轴，液压泵，控制阀，液压油箱和冷 却装置组成。对于混凝土全自动搅拌车，驱动器仍然非常重要，所以让我们仔细看看。

The driver is used to drive the rotation of the concrete tank. It consists of power take-off unit, cardan shaft, hydraulic pump, control valve, hydraulic oil tank and cooling device. For automatic concrete mixer, the driver is still very important, so let's take a closer look.

1.通用车削部件是故障部件。应及时填充润滑脂，并经常检查磨损情况，并及时修理和更换。车队应该有一个备用万向轴组件，以确保在发生故障时几分钟内恢复。

1. General turning parts are fault parts. Grease should be filled in time, wear should be checked frequently, and repaired and replaced in time. The fleet should have a spare cardan shaft assembly to ensure recovery in a few minutes in the event of a failure.

2.确保液压油清洁。混泥土自动搅拌车的工作环境不好，一定防止脏水泥砂进入液压系统。应根据手册的要求定期更换液压油。一旦检查发现水或沙子混入液压油中，一定立即停止液压系统并更换液压油。

2. Make sure the hydraulic oil is clean. The working environment of the automatic concrete mixer is not good, so it must prevent the dirty cement sand from entering the hydraulic system. The hydraulic oil should be changed regularly according to the manual. Once water or sand is found mixed in the hydraulic oil, stop the hydraulic system immediately and replace the hydraulic oil.

3.确保液压油冷 却装置有用。定期清洁液压油散热器，防止散热器被水泥堵住，检查散热器风扇是否正常运转，防止液压油温度超标。只要液压元件确保液压油清洁，通常几乎没有故障，但制造商具有不同的使用寿命。

3. Make sure that the hydraulic oil cooling device is useful. Regularly clean the hydraulic oil radiator to prevent the radiator from being blocked by cement. Check whether the radiator fan operates normally to prevent the hydraulic oil temperature from exceeding the standard. As long as the hydraulic components ensure that the hydraulic oil is clean, there are usually few failures, but manufacturers have different service lives.

一般情况下，如果驱动器由于故障停止工作，混凝土水箱将不能正常旋转，这将导致车辆中的混凝土报废，甚整个水箱混凝土将在水箱中冷凝，导致混凝土自动搅拌车报废。因此，驱动装置是否可靠是在使用中一定高度重视的问题。

In general, if the driver stops working due to fault, the concrete water tank will not rotate normally, which will lead to the scrapping of the concrete in the vehicle, or even the whole water tank concrete will condense in the water tank, resulting in the scrapping of the automatic concrete mixer. Therefore, whether the driving device is reliable or not is a problem of great importance in use.

以上对于混凝土全自动搅拌车的检查步骤和油泥带来的影响介绍就是这样了，希望对你有帮助。

The above inspection steps for the automatic concrete mixer and the impact of sludge are introduced in this way, hoping to help you.